These Build Your Own (BYO) 4K 60 Hz HDMI Over LAN Matrix POE Switchers send a 4K 60 Hz HDMI signal to up to 450' using a single CAT6/7 cable to up to an unlimited number of Inputs & Outputs up to up to 450'. They are configured with multiple 4K 60 Hz POE HDMI Transceivers (TX), and multiple 4K 60 Hz POE HDMI Transceivers (RX), and an appropriate size Managed POE Ethernet Switch. These LAN matrix switches send any input, to any output, in any combination, or all outputs, all controlled with tablet app, and a PC.

A 4K 60 Hz 14x32 HDMI over LAN Matrix is shown in this picture showing the multiviewer, 2-video wall setups, 14-TXs, 32-RXs, a rack mounted 48-port managed ethernet switch with IGMP snooping, the Wireless iPad Controller, and 4-methods to control it.

4K 60 Hz HDMI Over LAN Matrix Switchers Key Features::

4-Ways to Configure: It supports (1) One to one, (2) One to many, (3) Many to one, and (4) Many to Many.
Wireless Real Time Video iPad Preview: Preview the source video on an iPad before sent it to the TVs. That means your iPad will show, in real time, the videos that are on, say, all your DirecTV receivers. If you have 6-DirecTV receivers all set to different channels you'll see 6-different real-time videos, not pictures, but real time video on the iPad. You then can send them, if you choose.
Apps & Windows Control: This LAN based HDMI Matrix Switcher allows any input to be routed to any output; or the same input to be routed to all outputs, or any combination all controlled with an iPad and Android App, wall mounted touchscreens, and a Windows PC.
4K 60 Hz Video Wall Support: You can create a system with Video Walls of any size, and quantity only limited by the number of outputs you have. The input & output HDMI resolutions support up to 4K 60 Hz.
4K 60 Hz Multi-viewer Support: It even supports a multi-viewer shown in the upper right corner of this picture. The Multi-viewer can show up to 9-windows on one TV or projector screen. 7 are shown on this picture.
Cascadeable Ethernet Switches: The managed ethernet switches be cascaded and still act as a one large matrix. This is great for multiple floors, multiple rooms, and even multiple buildings by using fiber between them. All the many TVs will be in perfect synch with each other. The Ethernet switch supports both copper (CAT6/7) and fiber network interfaces.
4K 60 Hz VLAN Support: Our LAN based HDMI Matrix Switchers can be installed on your existing LAN as they have VLAN capability. Our VLAN HDMI Matrix System uses VLAN technology to isolate and protect the HDMI signals from other traffic on your network.
KVM Support: 2-USB 1.1 ports allow a user to control multiple computers from 2-sets of keyboards, video monitors, and mice.
Build Your Own (BYO) or Buy 4K 60 Hz Pre-configured Systems: We offer two ways to purchase our systems, one is to Build Your Own (BYO) here, and the the other is buying one of our preconfigured systems.

Compare our 4K 60 Hz POE HDMI Over LAN Matrix Switchers Features vs Others:

Wireless Real Time Video Preview
iPad shows live source video
Supports a VLAN
AV Over IP w/POE Technology
Video Wall support
Multi-viewer up to 9-windows/screen
One Extender for TX & RX i.e.Transceiver
WIFI iPad & Android Apps
4K 60 Hz video over 1G Network Switch
Bandwidth is only 7 Mbps

Rename Sources & Displays on tablet
Latency is only 80ms
Windows software control
Video walls up to a 7x7 (49-TVs):

Any Size Video Walls
Any Qty Video Walls

Seamless 80 to 120ms switching
Unlimited Save & Recall presets
Plug & Play (DHCP IP address)
Supports UI custom control

2-USB ports for KVM
3rd party Open UDP commands
19" Rack cage up to 14-TXs
Extends HDMI to 450' w/CAT6
Supports H.264 & H.265 Protocol
SEC Security Compliance
HDCP compliant
Separate audio outs
Scalable Ins & Outs
Upgradeable to 100s of Ins & Outs

EXAMPLE: Build a WolfPack 4K 60 Hz 14x32 HDMI Over LAN Matrix System (See above picture):

14 - 4K 60 Hz POE HDMI over LAN Transmitters (Transceivers) to 450'
32 - 4K 60 Hz POE HDMI over LAN Receivers (Transceivers) to 450'
1 - POE Rack mount 48-Port 1G IGMP Managed Ethernet switch
1 - Wireless iPad Control & Ethernet switch (non-POE)

If you are looking for a high-quality, versatile, and easy-to-use 4K 60 Hz HDMI Over LAN Matrix Switcher, then this BYO is a great option. Got a question or special need? Call 833-WOLFPACK or 833-965-3722 right now to get a quote today.

Why not Build Your Own 4K 60 Hz HDMI Over LAN Matrix Switch today?

BYO 4K 60 Hz POE HDMI Over LAN Matrix Switch Specs:

4K 60 Hz video over an 1G Switch
Renaming of the sources & displays
Zero configuration as it's plug and play
Resolution scaling on PC control software
OSD function to build video walls
Scalable
Field Upgradeable
HDMI 1.4 and HDCP 1.4 Compliancy
Bandwidth is ~30 MBS

POE or powered w/provided power supply
Uses DHCP for the IP settings
PC Software for IP address, video wall, EDID etc settings
3.5mm audio on TX & RX
EDID preset & learning
50ms latency in Low mode
250ms latency in High mode
Both a Video Wall mode & a matrix switch mode
iPad & Android Apps & PC Software control

Resolutions Supported:

640 x 480@60Hz, 480p@60Hz
576P@50Hz, 800 x 600@60Hz
1024 x 768@60Hz, 720p@50Hz
720p@60Hz, 1280 x 800@60Hz
1280 x 1024@60Hz, 1366 x 768@60Hz
1400 x 1050@60Hz, 1440 x 900@60Hz
1680 x 1050@60Hz, 1920 x 540@60Hz
1080p@24Hz, 1080p@25Hz
1080p@30Hz, 1080p@50Hz
1080p@60Hz, 4K@30Hz

Why not Build Your Own 4K 60 Hz HDMI Over LAN Matrix Switch today?

Brochure for 4K 60 Hz POE HDMI Over LAN Matrix Switch - Doc

Brochure for 4K 60 Hz POE HDMI Over LAN Matrix Switch - PDF

User Manual for 4K 60 Hz POE HDMI Over LAN Matrix Switch with Xview Control - Doc

User Manual for 4K 60 Hz POE HDMI Over LAN Matrix Switch with Xview Control - PDF

How to add the IPC to the BYO-AVLAN-4K60 AV over IP System - Doc

How to add the IPC to the BYO-AVLAN-4K60 AV over IP System - PDF

BYO-AVLAN-4K60 UDP_TCP Control API - Doc

Operation Guide for DesignEditor Software - Doc

Operation Guide for DesignEditor Software - PDF

Operation Guide for Operation Guide for DVSTool_Xview Software - Doc

Operation Guide for Operation Guide for DVSTool_Xview Software - PDF

Link to Apps and Software

iPad APP control for this AV over LAN System

AV over LAN System Installation Cage Assembling Guide

Why not buy a POE HDMI Over LAN Matrix Switch today?

WolfPack POE LAN Software and Apps

Why not Build Your Own 4K 60 Hz HDMI Over LAN Matrix Switch today?

Click here for the iOS APP Link

Click here for the Android APP Link

Plug-and-play PC software (AVIPlite)

Plug-and-play Android APK (AVIPlite)

PC configure, upgrade & control software (XView)

Customize control UI software (EditTool)

Customized control UI APK (DVSTool)

Why not Build Your Own 4K 60 Hz HDMI Over LAN Matrix Switch today?

Q: Can I use my own ethernet switch?
A: Usually, if it meets the specs:

1G bandwidth
Support IGMP snooping
Support multicast
Support fast-leave
Support POE

We suggest you get the complete system from us though as if there are any issues our support may be diminished. We will do our best to help you.

Q: Does the transmitter have an audio out?
A: Yes, the transmitter and receiver both have the 3-pin (Phoenix connector) audio output.

Q: How do you test before you ship my system?
A: We put the products in the heating room for 12-hours for aging and have all the products turned On and the temperature of the heating Room set to 140 degrees. If anything fails we replace the failed unit and start the test over again.

Q: Is it a picture of a screen or full-motion video?
A: The preview of both sources and the Video wall is with full-motion video.

Q: Is there audio with the iPad Preview screen?
A: No, the preview on the iPad will not have the audio function.

Q: Can there be more than one showing?
A: For the source preview, it can show all the sources. The TV/Video Wall will be only showing the one that is selected.

Q: Is it a source only?
A: This preview is for both input sources, and the selected TV or video wall

Q: Can it be at TV at the destination?
A: Do you mean to have this preview function on the TV? If so, it's not able to do it, as the preview function is only available on the iPad APP. Unless we wirelessly share/mirror the iPad to the Apple TV by airplay.

Q: Can there be text written below the picture or video?
A: We can add the OSD picture on any position of the TV. I am working on a demo video of this, but this will need to use the PC control software to add.

Q: If it is a satellite receiver can you change the channel?
A: No, we will only be able to preview the contents, but not able to change the channels

Q: If a DVD is playing do you see a picture?
A: Yes, we will see exactly the same contents as the DVD plays.

Can the Ethernet switches be cascaded and still act as a matrix?
A: Yes. The network switches can be cascaded and still act as a large matrix.

Q: Is it a WEB GUI control or PC software
A: It is a PC control software-based system for the configurations like CEC settings, resolution, IP addresses, etc . It also has an optional iPad app and does not have web GUI control.

Q: How do you setup the video wall?
A: For the video wall set up, it can done it in seconds using the iPad or Android app.

Q: How do you change the IP and MAC address of the transmitters and receivers?
A: You can set up the IP and MAC on the iPad app or PC control software, but we recommend using the automatic IP and MAC address, so it can support plug and play.

Q: The Transmitters and Receivers both have Audio out on the receiver can the audio be matrixed such as Receiver A sends audio out to Receiver B, if using the audio out?
A: The audio out on both the RX and TX are the corresponding audio with the video so its audio function is only an extract function from the video and is not able to do as an audio matrix.

Q: On the IP control box there are (2) LAN ports, would that be for 2 separate LANs?
A: We will only need to use the LAN 1 for the controlling & settings and for the broadcast version:

LAN1 (AV/POE): To connect with the network switch use the PC control software to control this system
LAN2 (C): To connect with the network switch this is used for a 3rd party to use the IP control this system

Q: What is it a distance with POE in and out?
A: With the POE, the input can up to 100m (330 ft) at 4K 60 Hz and the output also is 100m (330 ft)

Q: What is the distance without POE using the AC adapters in and out?
A: It is also the same distance as the POE distance as in and out both are 100m (330 ft)

Q: What type of UTP cable do you recommend?
A: As it's using for the video signal transmission we recommend using the STP 868B cable

Q: Can you use CAT6 - 5E - 6 and 7 and is there a difference in length of cables?
A: We did the tests here with the CAT6/CAT6/Cat6/Cat7 cable and the CAT6 and CAT7 are the best and can reach a distance of 450 feet with POE

Q: Please give us an explanation of when the large and small streaming resolutions would be used?
A: The highest resolution can up to 4K 60 Hz, the lowest resolution is 680x480@60Hz but that resolution can't support IP camera decoding

Q: What does the PC Software do?
A: The PC control software is mainly for the resolutions, RS232, image adjustment and RX/TX IP settings

Q: Does the iPad control require a wireless router?
A: Yes, it will need a WIFI router connected in the same system

Q: In the diagram in the manual it shows the IP control box with only an Internet connection, does a PC plug into it?
A: Yes, the control PC uses a LAN cable connected to the same network switch

Q: You also recommend Managed POE switches, correct?
A: We tested on several POE network switches and so far both of the managed POE or the non-managed POE network are working well. But the managed network switch is more stable and it's fanless which is quieter.

Q: Can I use any network switch/router to access and utilize this system?
A: No, it will need the network and router to be 1000Mbps bandwidth for this AV over IP system. As each AV over IP device will take about 20-Mbps bandwidth.

Q: Can it be set up on an existing network, possibly on its own VLAN and WiFi network? Or does it need to be completely isolated.
A: We recommend the isolated network for the AVoverIP system, but if you are familiar with the VLAN and WIFI settings, you also can use with the existing network, but still need to make sure the network switches for AV over IP system need to be 1 Gigabit type.

Q: Can I use any Android Tablet to configure the system?
A: Yes, as this AV over IP system supports the Android APP, but we recommend the Android 7 and above version. We also have the POE Android tablet for selections.

Q: If the number of devices exceeds the 48 port switch threshold, can I run it through multiple switches if they are all on the same VLAN if I can connect it to the existing network? Or if separated just daisy chain the switches?
A: Yes, we can run multiple switches and I usually do is just have a LAN cable to connect those switches. I have tested up to 7 switches in one system. To work with the existing network, the best to have VLAN settings or at least using the static IP addresses will be better to avoid the IP nonfiction.

Why not buy a 4K 60 Hz HDMI Over LAN Matrix Switch today?

Demo videos of HDTV Supplys WolfPack HDMI over LAN system simple plug and play system with the seamless switching, a video wall function, matrix switch capability.